HM-1001 Hemmer

One side of our hemmer creates a 1/2" hem, while the other side creates a 3/4" kickout at 45 Degrees. Having a hemmer increases productivity and also takes steps out that you do not have to worry about in your press. It keeps the same consistency with your angle degree all the  way down your trim. Great for eave trim, corners and rake trim.

Give us a call today to find out more information about our hemmers at 229-686-5385 or 229-599-2873 or visit us at griffinironwerks@windstream.net

Griffin Iron Werks 17 Stand Rollformer Synchronized

Griffin Iron Werks - LMF-914.17 Stand Rollformer
$55,000
griffinironwerks@windstream.net
mikegriffin01@windstream.net
Give us a call at (229) 599-2873 or (229) 686-5385. Come see our many rollformers and equipment.

900.11  LMF Ag panel Rollformer - Griffin Iron Werks

This is our LMF ag panel rollformer. We have a package deal right now that includes the 11 station rollformer, post cut hydraulic shear, manual decoiler, computerized plc and a 10ft setoff table 30k .


This is the first of several vidoes we will be shooting. This one covers the basic without any material in the rollformer and shows the computer, rollformer operation and post cut hydraulic shear operation.


if you need more information, please contact us at 229-686-5385.
We also can be contacted via e-mail at griffinironwerks@windstream.net or mikegriffin01@windstream.net.

 


Slitter - Slits up to 48-3/8” Wide Material. 3 sets of blades
240 Volt Single Phase.

$6,800

We also have other NEW and REFURBISHED machines in stock! Financing is Available. Please Call Mike Griffin at Griffin Iron Werks for more information.

Office: (229) 599-2873 or (229) 686-5385

Hemmer - One side makes an ½” Hem and the other side makes a ¾” Kick Out at 45° angle. 240 Volt Single Phase.

We also have other NEW and REFURBISHED machines in stock! 

$7,200

Please Call Mike Griffin at Griffin Iron Werks

for more information.

Office: (229) 599-2873 or (229) 686-5385

10-6" Press Brake - Hydraulic pedal control -4 sided bottom die.

$12,000

Griffin Iron Werks - Nashville, Georgia

www.griffinironwerks.net
Mike Griffin - Owner
mikegriffin01@windstream.net
Give us a call at (229) 599-2873 or (229) 686-5385

Ridge Cap Rollformer

Approximately 7" each side with Hems. Rollforms on 4/12 slope which can be used from 1/12 to 10/12. You would need to add blanks.
$26,000 Financing is Available!
We also have other NEW and REFURBISHED

machines in stock! 


Please Contact Mike Griffin at Griffin Iron Werks:
Office: (229) 599-2873
After Hours: (229) 686-5385
www.griffinrionwerks.net

Griffin Iron Werks Auto Decoiler

5 ton Auto Decoiler - load up to 10,000# coils. 220v Single Phase, Hydraulic pump controls up, down, in, out, mandrel expand and mandrel contract.

$18,500. 

Please Contact Mike Griffin at Griffin Iron Werks:
Office: (229) 599-2873
After Hours: (229) 686-5385
www.griffinrionwerks.net

CNC - 10-6" Press Brake 

Servo Dies, Back Stop Gauges, Programmable, Can Break Up To 1/4 inch Flat Plate, Dual Pumps.

$49,900

Please Contact Mike at Griffin Iron Werks for more Information.

Office: (229) 599-2873
After Hours: (229) 686-5385

​GRIFFIN IRON WERKS

229-686-5385

229-599-2873

229-543-1158

268 Griffin Pond Lane

Nashville, Georgia 31639

  • Pinterest Social Icon
  • Wix Facebook page
  • Wix Twitter page

©  Copyright 2017